Ramp-Up offers you a quick and easy installation. First, you center your pre-finished mat, tape the perimeter, trowel down the SSTDRU859 adhesive, replace the mat in the wet adhesive and float up the edges and seams to form a watertight seal. Pull your tape and you are done!

Ramp Up still offers you the same low profile and zero trip point as our Traditional system offers, except now it can be installed in less than half the time. There are no mechanical fasteners or anchors needed to secure Ramp Up. There is no need to demo and re-pour existing curb ramps to accommodate your ADA truncated dome requirements.

The post Ramp Up (Glue Down) appeared first on Truncated Dome Pros.

Built Up is a Peel ‘n Stick mat that is easy and quick to install. Installs in minutes and requires no special tools. No drilling or anchoring is required.

MEETS ALL ADA REQUIREMENTS

The Built Up system is an ADA compliant patterned mat with a high contrast, low profile, slip-resistant surface. All ADA guidelines for ADAAG section 4.29.2 ADA compliant truncated-done tactile warning system for pavement are met.

PERFECT FOR ASPHALT APPLICATIONS

The adhesive used in Built Up is ultra-strong, heavy-duty and long-lasting. It is secure and fast and will stick to anything. Space age technology makes the mat weather, UV, water and temperature-resistant.

INSTALLS IN MINUTES

Save time and money when it comes to installation. Easily installed by one person with minimal preparation required. If you’re currently sending out a crew to install ADA mats you are wasting money. Start saving money today with the easy to install Built Up ADA surface mount mat.

The post EquaLite Built UP appeared first on Truncated Dome Pros.

ADA COMPLIANCE

2.35″ center-to-center, in-line dome spacing meets ADA Federal and State requirements

Truncated dome size and spacing compliant with ADA Federal and State requirements, 0.9″ base and 0.45″ top diameter

Fully complies with all ADA and OSHA requirements for surface height transitions to eliminate trip hazards

Consistent dome spacing when tiles are adjoined (side-by-side or end-to-end)

Wide in-line dome configuration facilitates a smooth rolling transition for strollers, wheelchairs and walkers

Audible detectability technology engineered for sound amplification

Engineered load transfer design with bosses located directly under domes transfer loads directly to substrate

Beveled perimeter edge meets ADA vertical displacement requirements

Strategically placed pre-formed fastener hole locations enhance installation integrity and provide easy installation

Tiles shipped with color-matched fasteners

Adhesive location identified on reverse side of tile for easy, error-free installation

Tactile Bond/Sealant is available through all our authorized distributors. The system is designed and tested to be both a structural adhesive and perimeter edge sealant

Interactive sizes – all tiles maintain pattern repeat when mounted side-to-side or top-to-bottom

The post Surface Applied appeared first on Truncated Dome Pros.

Twenty years of tactile design, testing and manufacturing insights have gone into Access Tile’s superior engineered detectable warning product. Access Tile boasts the easiest and fastest installation in the industry requiring no concrete demolition and needing only a single fastening device. The replaceability feature of the tile is industry leading due to its simplicity and speed.

2.35″ center-to-center, in-line dome spacing meets ADA Federal and State requirements

Truncated dome size and spacing compliant with ADA Federal and State requirements, 0.9″ base and 0.45″ top diameter

Fully complies with all ADA and OSHA requirements for surface height transitions to eliminate trip hazards

Consistent dome spacing when tiles are adjoined (side-by-side or end-to-end)

Wide in-line dome configuration facilitates a smooth rolling transition for strollers, wheelchairs and walkers

Installs in minutes during cement finishing stage

The replaceability feature of the tile is industry leading due to its simplicity and speed

Tamper-proof, stainless steel fastener maintains flush interface with walking surface

Corrosion resistant hexagonal anchors designed to entrap concrete for optimal anchoring

Anchor and fastener material compositions allow for reliable and secure installations when multiple replacements are necessary

Large interface between tile and anchor seat area maximizes support at each fastener location

Multiple fastener locations to ensure full anchoring of tactile surface

Structural spine ensures stiffness and strength

Tiles shipped with removable protective plastic film to provide a clean surface after installation

Interactive sizes – all tiles maintain pattern repeat when mounted side-to-side or top-to-bottom

The post Cast-In-Place (Replaceable) appeared first on Truncated Dome Pros.

For use in Retrofit applications

Large perimeter beveled edges for smooth transition

Secured with color-matched fasteners and structural adhesive

Surface applied tiles are 1/8″ thick with beveled edges

Standard sizes: 24″ x 36″, 24″ x 48″, 24″ x 60″, 36″ x 48″, and 36″ x 60″

Surfaced Applied Tactile, available in both Rectangular and Radius, is made of a colorfast and UV stable homogenous glass and carbon composite with fiberglass truncated domes for enhanced durability. The Surface Applied Tactile is used to retrofit over an existing concrete substrate and can be installed in as little as 10 minutes.

All of our truncated dome tactile surfaces are in full compliance with the American Disabilities Act Accessibility Guidelines (ADAAG), Public Right-of-Way (PROW), and California Title 24 Requirements. ADA Solutions

Features and Advantages:

0.1875” thick with beveled outer perimeter for safe transitions

Includes 10oz. tube of Chemlink M1 Structural Adhesive

Includes nylon sleeve anchors and stainless steel fasteners

Can be installed within 5 minutes

Applications

Municipal governments and local businesses across the country use tactile warning surfaces to help pedestrians navigate sidewalks, ramps, and entryways. ADA domes assure safety and accessibility no matter the location or application. Each tactile system in our product line meets all local, state, and federal detectable warning surface requirements, so customers never have to worry about compliance issues.

Surface applied truncated domes from ADA Solutions, Inc. are perfect for retrofit projects. We build our detectable warning pavers with beveled edges for a smooth, safe transition. Choose between two different warning tile configurations—radius and rectangular. Color-matched fasteners and structural adhesives make tactile surface installation easy and secure.

The post Surface Applied appeared first on Truncated Dome Pros.

For use in new curb ramps or new construction

Pressed into place in freshly poured concrete

Cast-In-Place Tiles have a 1/4″ nominal thickness and feature embedment ribs 3″ on center through entire length of tile

Plastic sheeting protection covers entire surface of Cast-In-Place Tile

Standard sizes: 24″ x 36″, 24″ x 48″, 24″ x 60″, 36″ x 48″, and 36″ x 60″

Features and Advantages:

Raised truncated domes with a diameter of nominal 0.9” and a height of 0.2”

Body Thickness is 0.25” not including truncated domes

Does not rely on any type of paint coating to achieve color stability

The Cast in Place Tactile Surface is made of a colorfast and UV stable homogenous glass and carbon composite with fiberglass truncated domes for enhanced durability. The Cast in Place Tactile Surface is used for new curb ramps or new construction applications and is a great long-term solution for any project, under any weather conditions.

All of our truncated dome tactile surfaces are in full compliance with the American Disabilities Act Accessibility Guidelines (ADAAG), Public Right-of-Way (PROW), and California Title 24 Requirements. ADA Solutions Inc. products are approved for use by all major municipalities, DPWs, and state DOTs.

The post Cast-in-Place appeared first on Truncated Dome Pros.